| Main Page | Shadow Forums | Motorcycle Links | Shadowrider's Photo Gallery | Today's Posts | New Posts |



DO NOT POST NUDITY OR PORN OR IT WILL BE DELETED! Thank you.

  
Go Back   Shadowriders > Honda Shadow Discussion Forums > Shadow VLX Modifications
User Name
Password
Reply
 
Thread Tools Display Modes

Steed 600 mods
Old 02-19-2017, 04:36 PM   #1
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
Steed 600 mods

Thought id put up some photos of my steed mods,
Ive got lots of pics i'll upload some over the next few days with a little info of what I've done. There's prob a few things I've forgotten to put on the list.

List of work:
Replace fibreglass rear fender with steel
Fab new frame under seat where the cluster fuck of steel is
led indicators on rear swing arm
led indicators rebated into handle bars
Make new handle bars
Delete switch housings on bars replace with momentary micro switches
Delete the fuel pump/vac cutoff whatever the fuck that thing is
Weld fuel tap into tank x
New grips and throttle tube
Delete light up dash (fuel/high beam/ indicators)
Delete kill switch safety stuff Like the stand cut off and clutch safety
Delete key ignition
Install Three toggle switches for on/off kill switch and starter
clean up the wiring
Fab and relocate battery box
Remove and relocate new coolant overflow
Remove air box
carby stax/rejet
Cut off all the little welded wiring tabs to clean the frame up
Lift front of the petrol tank up
relocate coils under the tank

This is how it sat after the first set of mods chopping seat frame etc..[IMG]http://[/IMG]

Last edited by Justo : 02-19-2017 at 04:46 PM.
  Reply With Quote

Old 02-19-2017, 04:45 PM   #2
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
This is the section of frame getting replaced
[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]
  Reply With Quote

Old 02-21-2017, 04:15 PM   #3
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]
  Reply With Quote

Old 02-21-2017, 04:24 PM   #4
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]
  Reply With Quote

Old 02-21-2017, 04:31 PM   #5
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
[IMG][/IMG]

[IMG][/IMG]
  Reply With Quote

Old 02-24-2017, 05:31 PM   #6
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
New Bar setup done with recessed indicators, new throttle tube/grips and micro switches , same style as before just with a wider centre section to allow for indicators.

[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
  Reply With Quote

Old 03-01-2017, 12:11 AM   #7
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]


[IMG][/IMG]
  Reply With Quote

Old 03-03-2017, 04:36 AM   #8
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
This is how its looking at the moment needs electrical storage sorted out and coolant over container, but i just decided to make it rigid i should of just done it in the first place. I didn't cause i got a bad back and S.A roads are shit but i figure go hardtail or go home.
So new list:
Rigid frame
Re mount rear fender
Sort out coolant over flow had a temp bottle on there
New seat pan

[IMG][/IMG]

[IMG][/IMG]
  Reply With Quote

Old 03-10-2017, 07:19 PM   #9
HeyYoDho
Noob
 
HeyYoDho's Avatar
 
HeyYoDho is Offline
Join Date: Oct 2013
Location: Sacramento, CA
Posts: 18
I'm pretty jealous of your springer.
  Reply With Quote

Old 03-11-2017, 05:45 PM   #10
Justo
Noob
 
Justo's Avatar
 
Justo is Offline
Join Date: May 2016
Location: Australia
Posts: 13
So i started the hard tail conversion yesterday got a little bit done
[IMG][/IMG]

[IMG][/IMG]
  Reply With Quote



Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is On
Forum Jump



All times are GMT -4. The time now is 04:44 PM.


vBulletin skin developed by: eXtremepixels
Powered by vBulletin® Version 3.6.7
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.